Dicromantispa interrupta

Dicromantispa interrupta
Mantisfly

Wednesday, November 18, 2026

Torrey and Yew Propagation 2026

This blog post lays out how I processed the Florida Torrey (Torreya taxifolia) and Florida Yew (Taxus floridanus) reproductive materials that I was given this autumn. The materials consisted of 47 torrey seeds from a Georgia location and another 60 from a North Carolina site, torrey branch cuttings from five North Carolina plants, and a half-dozen or so each of male and female yew tree branch cuttings. I have successfully germinated torrey seeds in the past in 1-gal pots and in germination trays, using potting mix in some years and sawdust + planer shavings in other years. It typically takes two winters (double stratification) for torrey seeds to germinate. 

My old seed trays have finally seen the end of their days. They may be more than ten years old, but that’s a pretty good lifetime for pressure-treated inch-thick pine deck boards. They have germinated plenty of seeds for me in their time. I constructed three new ones over the past two weeks, each being appx 36 x 18 x 5.5 inches in size. As before, the new frames are made of PT pine deck boards, have a floor of half-inch galvanized hardware cloth, and an inset of nylon window screening. The former keeps rodents out, and the latter keeps bugs from invading from the ground below and keeps the potting mix in.

The GA seeds were already cleaned of their testas (husks) when I was given them, but I had to remove the testas from the NC seeds. Removal is simple, you just peel and rinse. However, within only a couple of days, the NC seeds were covered with fungal mycelia, so I soaked them in hydrogen peroxide for 5 – 10 minutes for semi-sterilization. The GA seeds were dry when I got them, and had so little fungus that I elected not to treat them.

The trays were filled to a depth of four inches with a potting mix of two-thirds organics plus one-third perlite. I then laid out 32 GA torrey seeds in tray #1 and 15 more GA torrey seeds in tray #2 (I realize the pic of tray #1 shows more than 32, but the extras were removed):

This next photo illustrates the seeds being set appx four inches apart and one inch deep in the potting mix:

Next, I added 35 NC torrey seeds to tray #2. These were separated into 14 ‘sinkers’ and 11 ‘floaters.’ I have gotten mixed opinions on floaters vs sinkers regarding seed viability, so I am testing that issue. The remaining 25 NC torrey seeds, all floaters, were set into tray #3. Having room for more seeds in #3, I added three chestnut oak acorns (Quercus montana), eight Kentucky coffeetree beans (Gymnocladus dioicus), and 15 persimmon seeds (Diospyros virginiana). Lastly, the trays were covered with framed half-inch galvanized hardware cloth.

I have never tried to root torrey or yew cuttings, but having been given some of each plus detailed instructions from a fellow Torrey Guardian, I decided to try. I stripped off most of their needles, wetted and coated their bases with rooting hormone, and imbedded them within 1-gal pots containing a potting mixture similar to what went into the seed trays. This photo shows them in my basement after I potted them. The two greenies up front are yews, the one on the left containing male cuttings and on the right with female cuttings. The five pots in the back contain the torrey cuttings, each pot having twigs from only one of each of the five trees:


I stuck U-shaped wires into the pots:


 … and then covered them with semi-transparent plastic bags to retain moisture: 

Several years ago, I made a squirrel exclusion cage out of PT pine lathing and chicken wire. After using it for one year, I put it away in the basement with no thought of ever using it again. However, rather than risk squirrels destroying the cuttings, I resurrected the cage to protect them, and while I was at it to further protect the seed trays. The whole shebang is now in shade outside where it will winter-stratify and be kept moist by rainfall while remaining well-drained: